how to put roof under deck

DIY Under Deck Roof and Drainage system (Part 2) - YouTube

www.reneeromeo.com @reneeromeodiy #diylikeapro http://reneeromeo.com/category/construction/ http://reneeromeo.com/category/in-the-kitchen/ http://reneeromeo....【Get Price】

A Guide to Constructing a Flat Roofing System | Roof Stores

Warm Flat Roofing: This approach uses insulation with no air gap either immediately above or below the roof deck. A vapour control layer must be used below the insulation. This option avoids the requirement to ventilate the roof. Cold Flat Roofing: This is where the insulation is typically packed between the rafters. A 50mm air gap must be left.【Get Price】

Building Deck Over Garage Roof - How To Guide

If you’d like to build a deck over your roof make sure the roof has a covering that allows water to run off. You’ll most likely be able to build the deck on that. Even if your roof has a slight pitch you can level it off through the construction of the deck’s understructure.【Get Price】

How to Install Roofing Underlayment | DoItYourself.com

Step 7 – Finishing the Roof Underlayment. Continue the underlay process until the whole roof is complete. Install the overlayment over the roof ridge so that it overlaps by eight inches on both sides. Be sure there are no bumps or creases in the material. In places where the roof is attached to the wall position the materials four inches up.【Get Price】

Decks–Roofs You Can Walk On | Building Science

It is not on the top of the deck; it is underneath the deck. And it’s the wrong kind; it is air permeable. If it is underneath the deck it cannot be air permeable. Photograph 10: Condensation and Decay are Bad—Air permeable insulation under deck can lead to condensation and decay. You would never construct an unvented roof this way. So why.【Get Price】

Adding a roof under a deck - YouTube

Adding a sloped sheet metal roof under a deck to make a dry place to store outdoor stuff like the wheelbarrow or kids toys.http://woodgears.ca/deck/roof_und...【Get Price】

How to Build a Deck Cover: 13 Steps (with Pictures) - wikiHow

Cut your 6 in × 6 in (15 cm × 15 cm) posts to the height you need them to be. Cut them to the height of the roof or 7 ft (2.1 m) tall if you are making a free-standing deck cover. Use a circular saw to cut the corner posts to the right length. You can get the posts pre-cut at a lumber yard or home improvement center to save time.【Get Price】

10 steps how to install corrugated metal roofing

Cut the roofing felt to fit with a utility knife. The roofing felt will lay horizontally along the plywood deck of the roof. Attach the roofing felt with roofing staples. Make sure you overlap each layer by at least 4 inches.【Get Price】

How to Build a Deck on a Roof | Today's Homeowner

Much easier than even a home deck you just put them under there and screw them up the way you want them and they’re there. Danny Lipford: Well it’s great that you don’t have to penetrate the roof in any way. Because I’ve seen a lot of roof type decks and a lot of different ways of tarring around it. But after a few years and the.【Get Price】

Fastening a Patio Roof to the House | HomeTips

A house-attached patio roof takes advantage of the house’s structure by supporting one end of the roof on a ledger mounted horizontally to the house. The ledger typically a 2 by 6 is usually designed to hold one end of the patio-roof rafters. Locating and mounting the ledger is normally a fairly easy process; the ledger should be attached before the foundation is built for a deck patio.【Get Price】

Flat roof: timber deck insulated between and below joists.

Fit the cut Mannok Therm Roof / MR insulation boards tightly between the joists. A gap of 50mm must be left between the upper surface of the insulation layer and the timber deck above to form the ventilation cavity. Ventilation openings must be left at each end of every air space.【Get Price】

how to install roof panes under a deck

How to Install Corrugated Roof . . but a nearly-flat roof is fine for under-deck installations. 2 Install a wood support structure for your panels screwing a row of 2-by-4s running .【Get Price】